       Click your browser PRINT button to print this printer friendly page. |
Emergency Response Services
Calgon Carbon offers a wide variety of equipment, activated carbon and specialty products, and field personnel that will respond to the clients on a rapid response basis. Suitably sized treatment equipment and appropriate media can be quickly dispatched from well-maintained inventories to the application sites. Regional field personnel can supervise the equipment’s installation and provide operator training.
Dual Express
Calgon Carbon's Dual Express is a carbon adsorption system specifically designed to provide a rapid solution to a temporary problem. For emergency situations where quick response is critical, it can be dispatched to a customer's site within hours of notification and operation can begin immediately after set-up. Calgon Carbon personnel are available to supervise system start-up. The Dual Express is ideal for periodic or temporary use where a permanent system would not be economical, including:
For further information on Calgon Carbon's Dual Express, click here. Mobile Adsorption Service
Calgon Carbon maintains an inventory of trailer-mounted mobile adsorption equipment which can be dispatched, if necessary, on 24-hours notice. Moments after arrival on-site, with just two simple hose connections, the pre-piped Mobile Adsorber can be fully operational. The pre-piped mobile systems contain 14,000 pounds of granular activated carbon and are capable of treating up to 225 gpm of a liquid stream which equates to 15 minutes of carbon contact time.
For further information on Calgon Carbon's Mobile Adsorption Service, click here. Sales/Product Inquiries
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Liquid Phase Equipment |
|||
Equipment |
Pounds of Carbon |
Pressure (psig) |
Maximum Range (gpm) |
| FLOWSORB® | 180 |
5.0 recommended |
10 |
| Small DISPOSORB® | 165 |
7.5 maximum |
10 |
| Large DISPOSORB® | 1,000 |
7.5 maximum |
30 |
500-2,000 |
75 |
70 |
|
| Protect™ LM Series | 500-2,000 |
75 |
70 |
| Protect™ MD Series (2 vessels) | 1,000-4,000 |
75 |
70 per vessel, operated in series |
| CR-2000 | 2,000 |
50 |
100 |
| CR-5000 | 5,000 |
50 |
250 |
| CYCLESORB® FP1 | 1,000 |
75 |
30 |
| CYCLESORB® FP2 | 2,000 |
75 |
60 |
| CYCLESORB® HP | 2,000 |
75 |
60 |
| Model 6 (2 vessels) | 12,000 |
75 |
200 per vessel, operated in series |
| Model 8 (2 vessels) | 20,000 |
75-125 |
350 per vessel, operated in series |
| Model 10 (2 vessels) | 40,000 |
75-125 |
700 per vessel, operated in series |
| Model 12 (2 vessels) | 40,000 |
125 |
700 per vessel, operated in series |
| Mobile Adsorber | 14,000 |
35-65 |
250 |
| Dual Module (2 vessels) | 40,000 |
75 |
300 per vessel, operated in series |
| Dual Express (2 vessels) | 40,000 |
75 |
600 per vessel, operated in series |
Specific product information, product data sheets and MSDS's can be found in the following chart.
 Product Bulletin/Specification Sheet |
 Product Brochures |
 Material Safety Data Sheets (MSDS) |
 |
FLOWSORB® |
| Low pressure, 55-gallon lined metal drum with 180 lbs. of activated carbon for water treatment at 10 gpm or less. | |
|
DISPOSORB® Units |
| High-density polyethylene units in 2 sizes for water treatment up to 30 gpm. | |
|
Protect™ TW Series |
| 75 psi rated lined steel vessels, with PVC underdrains and distribution headers, holding 500–2,000 lbs of activated carbon for flows up to 90 gpm. | |
|
Protect™ LM Series |
| 75 psi rated lined steel vessels, upgraded design from the TW. Holds 500-2,000 lbs. of activated carbon for flows up to 90 gpm. | |
Protect™ MD Series |
|
| Series consists of 2 Protect LM adsorbers with connecting pipe rack allowing for series, parallel or lead/lag operation. | |
 |
CYCLESORB® FP Series |
| High-density polyethylene vessels wrapped with FRP to produce 75 psi rating. Used on a temporary service basis and returned to Calgon Carbon when the carbon becomes exhausted. Two sizes for flows up to 60 gpm. | |
|
CYCLESORB® and CYCLESORB® HP |
| Stainless Steel adsorbers holding 2,000 lbs of activated carbon. Used on a temporary service basis and returned to Calgon Carbon when the carbon is exhausted. Treat flows up to 60 gpm. | |
|
CR Series |
| Economical, epoxy lined steel adsorbers with PVC underdrains and PPL nozzles. 50 psi pressure rated. Two sizes for flows up to 250 gpm. Pipe rack is also available. | |
|
Model 6 |
| Two 6’ diameter ASME Code lined steel adsorbers with interconnecting pipe rack. Used to treat flows up to 225 gpm in series or 450 gpm in parallel. Designed for carbon slurry loading and discharge. | |
|
Model 8 |
| Two 8’ diameter ASME Code lined steel adsorbers with interconnecting pipe rack. Used to treat flows up to 400 gpm in series or 800 gpm in parallel. Designed for carbon slurry loading and discharge. | |
|
Model 10 |
| Two 10’ diameter ASME Code lined steel adsorbers with interconnecting pipe rack. Used to treat flows up to 700 gpm in series or 1,400 gpm in parallel. Designed for carbon slurry loading and discharge. | |
|
Model 12 |
| Two 12’ diameter ASME Code lined steel adsorbers with interconnecting pipe rack. Used to treat flows up to 700 gpm in series or 1,400 gpm in parallel. Designed for carbon slurry loading and discharge | |
|
Dual Module |
| Two 10’ diameter ASME Code lined steel adsorbers skid mounted with interconnecting pipe rack. Used to treat flows up to 350 gpm in series or 700 gpm in parallel. Designed for carbon slurry loading and discharge. Easily dispatched to treatment sites. | |
|
Dual Express |
| Two 8’ diameter ASME Code lined steel adsorbers with interconnecting pipe rack. Used to treat flows up to 300 gpm in series or 600 gpm in parallel. Designed for carbon slurry loading and discharge. Easily dispatched to treatment sites. | |
|
Mobile Adsorber |
| 8’ diameter ASME Code lined steel adsorber. Used to treat flows up to 225 gpm. Dispatched fully loaded to treatment sites. |
